This commit temporarily comments the copying of the negotiated CIDs
into the established ::mbedtls_ssl_transform in mbedtls_ssl_derive_keys()
until the CID feature has been fully implemented.
While mbedtls_ssl_decrypt_buf() and mbedtls_ssl_encrypt_buf() do
support CID-based record protection by now and can be unit tested,
the following two changes in the rest of the stack are still missing
before CID-based record protection can be integrated:
- Parsing of CIDs in incoming records.
- Allowing the new CID record content type for incoming records.
- Dealing with a change of record content type during record
decryption.
Further, since mbedtls_ssl_get_peer_cid() judges the use of CIDs by
the CID fields in the currently transforms, this change also requires
temporarily disabling some grepping for ssl_client2 / ssl_server2
debug output in ssl-opt.sh.
Part of the record encryption/decryption tests is to gradually
increase the space available at the front and/or at the back of
a record and observe when encryption starts to succeed. If exactly
one of the two parameters is varied at a time, the expectation is
that encryption will continue to succeed once it has started
succeeding (that's not true if both pre- and post-space are varied
at the same time).
Moreover, previously the test would take turns when choosing which
transform should be used for encryption, and which for decryption.
With the introduction of the CID feaature, this switching of transforms
doesn't align with the expectation of eventual success of the encryption,
since the overhead of encryption might be different for the parties,
because both parties may use different CIDs for their outgoing records.
This commit modifies the tests to not take turns between transforms,
but to always use the same transforms for encryption and decryption
during a single round of the test.
requires_config_enabled doesn't support multiple config options.
Tests having multiple configuration dependencies must be prefixed
with multiple invocations of requires_config_enabled instead.
When running make with parallelization, running both "clean" and "lib"
with a single make invocation can lead to each target building in
parallel. It's bad if lib is partially done building something, and then
clean deletes what was built. This can lead to errors later on in the
lib target.
$ make -j9 clean lib
CC aes.c
CC aesni.c
CC arc4.c
CC aria.c
CC asn1parse.c
CC ./library/error.c
CC ./library/version.c
CC ./library/version_features.c
AR libmbedcrypto.a
ar: aes.o: No such file or directory
Makefile:120: recipe for target 'libmbedcrypto.a' failed
make[2]: *** [libmbedcrypto.a] Error 1
Makefile:152: recipe for target 'libmbedcrypto.a' failed
make[1]: *** [libmbedcrypto.a] Error 2
Makefile:19: recipe for target 'lib' failed
make: *** [lib] Error 2
make: *** Waiting for unfinished jobs....
To avoid this sort of trouble, always invoke clean by itself without
other targets throughout the library. Don't run clean in parallel with
other rules. The only place where clean was run in parallel with other
targets was in list-symbols.sh.
* origin/pr/2403: (24 commits)
crypto: Update to Mbed Crypto 8907b019e7
Create seedfile before running tests
crypto: Update to Mbed Crypto 81f9539037
ssl_cli.c : add explicit casting to unsigned char
Generating visualc files - let Mbed TLS take precedence over crypto
Add a link to the seedfile for out-of-tree cmake builds
Adjust visual studio file generation to always use the crypto submodule
all.sh: unparallelize mingw tests
all.sh - disable parallelization for shared target tests
config.pl: disable PSA_ITS_FILE and PSA_CRYPTO_STORAGE for baremetal
all.sh: unset crypto storage define in a psa full config cmake asan test
all.sh: unset FS_IO-dependent defines for tests that do not have it
curves.pl - change test script to not depend on the implementation
Export the submodule flag to sub-cmakes
Disable MBEDTLS_ECP_RESTARTABLE in full config
Export the submodule flag to sub-makes
Force the usage of crypto submodule
Fix crypto submodule usage in Makefile
Documentation rewording
Typo fixes in documentation
...
* origin/pr/2647:
list-symbols.sh: if the build fails, print the build transcript
Document "check-names.sh -v"
all.sh: invoke check-names.sh in print-trace-on-exit mode
Print a command trace if the check-names.sh exits unexpectedly
With MBEDTLS_USE_PSA_CRYPTO and MBEDTLS_ENTROPY_NV_SEED enabled, the
tests need a seedfile. Since test_suite_entropy is no longer there to
create it, and MBEDTLS_USE_PSA_CRYPTO is now enabled in the full
config, create tests/seedfile explicitly in basic-build-test.sh.
Sometimes, when building the shared target with crypto submodule, one could
get an "No rule to make target '../crypto/library/libmbedcrypto.so'" error.
This is due to two reasons - building in parallel and (probably) an
incomplete/incorrect list of dependencies for certain targets. The proposed
solution is to disable parallel builds with crypto submodule for now.
An issue has been raised here: https://github.com/ARMmbed/mbedtls/issues/2634
Sometimes, when building the shared target with crypto submodule, one could
get an "No rule to make target '../crypto/library/libmbedcrypto.so'" error.
This is due to two reasons - building in parallel and (probably) an
incomplete/incorrect list of dependencies for certain targets. The proposed
solution is to disable parallel builds with crypto submodule for now.
An issue has been raised here: https://github.com/ARMmbed/mbedtls/issues/2634
Currently the top-level makefile deploys commands to both Mbed TLS and
the submodule. Running make in the "tests" directory builds only the TLS tests.
The top level CMake on the other hand does not have the "tests" target defined,
so it also cannot be used, hence the raw "make".
Previously it was disabled as too experimental, which no longer holds. Also,
this option introduces new APIs, so it's not only about an internal
alternative (as the comment in config.pl used to state) - people who request a
full config should get all of the available APIs.
Adapt all.sh: now all builds with full config will also test this option, and
builds with the default config will test without it. Just to be sure, let's
have a build with full config minus this option.
Update documentation of MBEDTLS_USE_PSA_CRYPTO to reflect the status of the
new APIs it enables in Mbed TLS and why they're still opt-in.
Also enable it in scripts/config.pl full, as well as two storage options that
were only blacklisted from full config because they depended on
MBEDTLS_PSA_CRYPTO_C.
Adapt tests in all.sh:
- tests with submodule enabled (default) no longer need to enable it
explicitly, and no longer need runtime tests, as those are now handled by
all other test cases in this script
- tests with submodule disabled (old default) now need to disable it
explicitly, and execute some runtime tests, as those are no longer tested
anywhere else in this script
Adapt documentation in Readme: remove the section "building with submodule"
and replace it with a new section before the other building sections.
Purposefully don't document how to build not from the submodule, as that
option is going away soon.
* origin/pr/2530: (27 commits)
Style fix
Fix test data
Update test data
Add some negative test cases
Fix minor issues
Add ChangeLog entry about listing all SAN
Check that SAN is not malformed when parsing
Documentation fixes
Fix ChangeLog entry
Fail in case critical crt policy not supported
Update SAN parsing documentation
change the type of hardware_module_name member
Change mbedtls_x509_subject_alternative_name
Add length checking in certificate policy parsing
Rephrase x509_crt extension member description
Rephrase changeLog entries
Remove redundant memset()
Propogate error when parsing SubjectAltNames
Tidy up style in x509_info_subject_alt_name
Print unparseable SubjectAlternativeNames
...
* origin/pr/2538:
Remove unneeded whitespaces
Fix mingw CI failures
Initialize psa_crypto in ssl test
Fix missing tls version test failures
Fix typo
Fix ChangeLog entry location
Add changeLog entry
Add test for export keys functionality
Add function to retrieve the tls_prf type
Add tests for the public tls_prf API
Add public API for tls_prf
Add eap-tls key derivation in the examples.
Add ChangeLog entry
Add an extra key export function
Have the temporary buffer allocated dynamically
Zeroize secret data in the exit point
Add a single exit point in key derivation function
We've observed that sometimes check-names.sh exits unexpectedly with
status 2 and no error message. The failure is not reproducible. This
commits makes the script print a trace if it exits unexpectedly.
Make `mbedtls_x509_subject_alternative_name` to be a single item
rather than a list. Adapt the subject alternative name parsing function,
to receive a signle `mbedtls_x509_buf` item from the subject_alt_names
sequence of the certificate.
In x509_info_subject_alt_name() we silently dropped names that we
couldn't parse because they are not supported or are malformed. (Being
malformed might mean damaged file, but can be a sign of incompatibility
between applications.)
This commit adds code notifying the user that there is something, but
we can't parse it.
