On x32 systems, pointers are 4-bytes wide and are therefore stored in %e?x
registers (instead of %r?x registers). These registers must be accessed using
"addl" instead of "addq", however the GNU assembler will acccept the generic
"add" instruction and determine the correct opcode based on the registers
passed to it.
A new test for mbedtls_timing_alarm(0) was introduced in PR 1136, which also
fixed it on Unix. Apparently test results on MinGW were not checked at that
point, so we missed that this new test was also failing on this platform.
* mbedtls-2.1:
selftest: fix build error in some configurations
Timing self test: shorten redundant tests
Timing self test: increased duration
Timing self test: increased tolerance
selftest: allow excluding a subset of the tests
selftest: allow running a subset of the tests
selftest: fixed an erroneous return code
selftest: refactor to separate the list of tests from the logic
Timing self test: print some diagnosis information
mbedtls_timing_get_timer: don't use uninitialized memory
timing interface documentation: minor clarifications
Timing: fix mbedtls_set_alarm(0) on Unix/POSIX
Increase the duration of the self test, otherwise it tends to fail on
a busy machine even with the recently upped tolerance. But run the
loop only once, it's enough for a simple smoke test.
mbedtls_timing_self_test fails annoyingly often when running on a busy
machine such as can be expected of a continous integration system.
Increase the tolerances in the delay test, to reduce the chance of
failures that are only due to missing a deadline on a busy machine.
Print some not-very-nice-looking but helpful diagnosis information if
the timing selftest fails. Since the failures tend to be due to heavy
system load that's hard to reproduce, this information is necessary to
understand what's going on.
mbedtls_timing_get_timer with reset=1 is called both to initialize a
timer object and to reset an already-initialized object. In an
initial call, the content of the data structure is indeterminate, so
the code should not read from it. This could crash if signed overflows
trap, for example.
As a consequence, on reset, we can't return the previously elapsed
time as was previously done on Windows. Return 0 as was done on Unix.
The POSIX/Unix implementation of mbedtls_set_alarm did not set the
mbedtls_timing_alarmed flag when called with 0, which was inconsistent
with what the documentation implied and with the Windows behavior.
* restricted/pr/412:
Correct record header size in case of TLS
Don't allocate space for DTLS header if DTLS is disabled
Improve debugging output
Adapt ChangeLog
Add run-time check for handshake message size in ssl_write_record
Add run-time check for record content size in ssl_encrypt_buf
Add compile-time checks for size of record content and payload
In a previous PR (Fix heap corruption in implementation of truncated HMAC
extension #425) the place where MAC is computed was changed from the end of
the SSL I/O buffer to a local buffer (then (part of) the content of the local
buffer is either copied to the output buffer of compare to the input buffer).
Unfortunately, this change was made only for TLS 1.0 and later, leaving SSL
3.0 in an inconsistent state due to ssl_mac() still writing to the old,
hard-coded location, which, for MAC verification, resulted in later comparing
the end of the input buffer (containing the computed MAC) to the local buffer
(uninitialised), most likely resulting in MAC verification failure, hence no
interop (even with ourselves).
This commit completes the move to using a local buffer by using this strategy
for SSL 3.0 too. Fortunately ssl_mac() was static so it's not a problem to
change its signature.
Fix missing definition of mbedtls_zeroize when MBEDTLS_FS_IO is
disabled in the configuration.
Introduced by d08ae68237
Merge remote-tracking branch 'upstream-public/pr/1112' into mbedtls-2.1
