When invalidating a translation block, set an invalid flag into the
TranslationBlock structure first. It is also necessary to check whether
the target TB is still valid after acquiring 'tb_lock' but before calling
tb_add_jump() since TB lookup is to be performed out of 'tb_lock' in
future. Note that we don't have to check 'last_tb'; an already invalidated
TB will not be executed anyway and it is thus safe to patch it.
Backports commit 6d21e4208f382dd8ca1f7995a6dd9ea7ca281163 from qemu
With a vfio assigned device we lay down a base MemoryRegion registered
as an IO region, giving us read & write accessors. If the region
supports mmap, we lay down a higher priority sub-region MemoryRegion
on top of the base layer initialized as a RAM device pointer to the
mmap. Finally, if we have any quirks for the device (ie. address
ranges that need additional virtualization support), we put another IO
sub-region on top of the mmap MemoryRegion. When this is flattened,
we now potentially have sub-page mmap MemoryRegions exposed which
cannot be directly mapped through KVM.
This is as expected, but a subtle detail of this is that we end up
with two different access mechanisms through QEMU. If we disable the
mmap MemoryRegion, we make use of the IO MemoryRegion and service
accesses using pread and pwrite to the vfio device file descriptor.
If the mmap MemoryRegion is enabled and results in one of these
sub-page gaps, QEMU handles the access as RAM, using memcpy to the
mmap. Using either pread/pwrite or the mmap directly should be
correct, but using memcpy causes us problems. I expect that not only
does memcpy not necessarily honor the original width and alignment in
performing a copy, but it potentially also uses processor instructions
not intended for MMIO spaces. It turns out that this has been a
problem for Realtek NIC assignment, which has such a quirk that
creates a sub-page mmap MemoryRegion access.
To resolve this, we disable memory_access_is_direct() for ram_device
regions since QEMU assumes that it can use memcpy for those regions.
Instead we access through MemoryRegionOps, which replaces the memcpy
with simple de-references of standard sizes to the host memory.
With this patch we attempt to provide unrestricted access to the RAM
device, allowing byte through qword access as well as unaligned
access. The assumption here is that accesses initiated by the VM are
driven by a device specific driver, which knows the device
capabilities. If unaligned accesses are not supported by the device,
we don't want them to work in a VM by performing multiple aligned
accesses to compose the unaligned access. A down-side of this
philosophy is that the xp command from the monitor attempts to use
the largest available access weidth, unaware of the underlying
device. Using memcpy had this same restriction, but at least now an
operator can dump individual registers, even if blocks of device
memory may result in access widths beyond the capabilities of a
given device (RTL NICs only support up to dword).
Backports commit 1b16ded6a512809f99c133a97f19026fe612b2de from qemu
Setting skip_dump on a MemoryRegion allows us to modify one specific
code path, but the restriction we're trying to address encompasses
more than that. If we have a RAM MemoryRegion backed by a physical
device, it not only restricts our ability to dump that region, but
also affects how we should manipulate it. Here we recognize that
MemoryRegions do not change to sometimes allow dumps and other times
not, so we replace setting the skip_dump flag with a new initializer
so that we know exactly the type of region to which we're applying
this behavior.
Backports commit ca83f87a66d19fdaabf23d4f5ebb49396fe232c1 from qemu
Instead of using -1 as end of chain, use 0, and link through the 0
entry as a fully circular double-linked list.
Backports commit dcb8e75870e2de199db853697f8839cb603beefe from qemu
Header guard symbols should match their file name to make guard
collisions less likely. Offenders found with
scripts/clean-header-guards.pl -vn.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Backports commit 121d07125bb6d7079c7ebafdd3efe8c3a01cc440 from qemu
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Backports commit a9c94277f07d19d3eb14f199c3e93491aa3eae0e from qemu
There are functions tlb_fill(), cpu_unaligned_access() and
do_unaligned_access() that are called with access type and mmu index
arguments. But these arguments are named 'is_write' and 'is_user' in their
declarations. The patches fix the arguments to avoid a confusion.
Backports commit b35399bb4e9968296a12303b00f9f2066470e987 from qemu
Some architectures (e.g. ARMv8) need the address which is aligned
to a size more than the size of the memory access.
To support such check it's enough the current costless alignment
check implementation in QEMU, but we need to support
an alignment size specifying.
Backports commit 1f00b27f17518a1bcb4cedca49eaec96a4d560bd from qemu
It doesn't make sense to pass a NULL ops argument to
memory_region_init_rom_device(), because the effect will
be that if the guest tries to write to the memory region
then QEMU will segfault. Catch the bug earlier by sanity
checking the arguments to this function, and remove the
misleading documentation that suggests that passing NULL
might be sensible.
Backports commit 39e0b03dec518254fabd2acff29548d3f1d2b754 from qemu
Provide a new helper function memory_region_init_rom() for memory
regions which are read-only (and unlike those created by
memory_region_init_rom_device() don't have special behaviour
for writes). This has the same behaviour as calling
memory_region_init_ram() and then memory_region_set_readonly()
(which is what we do today in boards with pure ROMs) but is a
more easily discoverable API for the purpose.
Backports commit a1777f7f6462c66e1ee6e98f0d5c431bfe988aa5 from qemu
The IOMMU driver may change behavior depending on whether a notifier
client is present. In the case of POWER, this represents a change in
the visibility of the IOTLB, for other drivers such as intel-iommu and
future AMD-Vi emulation, notifier support is not yet enabled and this
provides the opportunity to flag that incompatibility.
Backports commit d22d8956b185c002b50a4d0883aff61f857347ef from qemu
Every IOMMU has some granularity which MemoryRegionIOMMUOps::translate
uses when translating, however this information is not available outside
the translate context for various checks.
This adds a get_min_page_size callback to MemoryRegionIOMMUOps and
a wrapper for it so IOMMU users (such as VFIO) can know the minimum
actual page size supported by an IOMMU.
As IOMMU MR represents a guest IOMMU, this uses TARGET_PAGE_SIZE
as fallback.
This removes vfio_container_granularity() and uses new helper in
memory_region_iommu_replay() when replaying IOMMU mappings on added
IOMMU memory region.
Backports the relevant parts of commit f682e9c244af7166225f4a50cc18ff296bb9d43e from qemu
For some workloads such as arm bootup, tb_phys_hash is performance-critical.
The is due to the high frequency of accesses to the hash table, originated
by (frequent) TLB flushes that wipe out the cpu-private tb_jmp_cache's.
More info:
https://lists.nongnu.org/archive/html/qemu-devel/2016-03/msg05098.html
To dig further into this I modified an arm image booting debian jessie to
immediately shut down after boot. Analysis revealed that quite a bit of time
is unnecessarily spent in tb_phys_hash: the cause is poor hashing that
results in very uneven loading of chains in the hash table's buckets;
the longest observed chain had ~550 elements.
The appended addresses this with two changes:
1) Use xxhash as the hash table's hash function. xxhash is a fast,
high-quality hashing function.
2) Feed the hashing function with not just tb_phys, but also pc and flags.
This improves performance over using just tb_phys for hashing, since that
resulted in some hash buckets having many TB's, while others getting very few;
with these changes, the longest observed chain on a single hash bucket is
brought down from ~550 to ~40.
Tests show that the other element checked for in tb_find_physical,
cs_base, is always a match when tb_phys+pc+flags are a match,
so hashing cs_base is wasteful. It could be that this is an ARM-only
thing, though. UPDATE:
On Tue, Apr 05, 2016 at 08:41:43 -0700, Richard Henderson wrote:
> The cs_base field is only used by i386 (in 16-bit modes), and sparc (for a TB
> consisting of only a delay slot).
> It may well still turn out to be reasonable to ignore cs_base for hashing.
BTW, after this change the hash table should not be called "tb_hash_phys"
anymore; this is addressed later in this series.
This change gives consistent bootup time improvements. I tested two
host machines:
- Intel Xeon E5-2690: 11.6% less time
- Intel i7-4790K: 19.2% less time
Increasing the number of hash buckets yields further improvements. However,
using a larger, fixed number of buckets can degrade performance for other
workloads that do not translate as many blocks (600K+ for debian-jessie arm
bootup). This is dealt with later in this series.
Backports commit 42bd32287f3a18d823f2258b813824a39ed7c6d9 from qemu
This will be used by upcoming changes for hashing the tb hash.
Add this into a separate file to include the copyright notice from
xxhash.
Backports commit dc8b295d05ec35a8c032f9abca421772347ba5d4 from qemu
The function cpu_resume_from_signal() is now always called with a
NULL puc argument, and is rather misnamed since it is never called
from a signal handler. It is essentially forcing an exit to the
top level cpu loop but without raising any exception, so rename
it to cpu_loop_exit_noexc() and drop the useless unused argument.
Backports commit 6886b98036a8f8f5bce8b10756ce080084cef11b from qemu
The WORDS_ALIGNED #define is not used anywhere, and hasn't been since
2013 when commit 612d590ebc6cef rewrote the various ld<type>_<endian>_p
functions to not use it. Remove the #define and the comment describing it.
Also remove the line in the comment about TARGET_WORDS_ALIGNED, since
it has never actually existed.
Backports commit 0d5c21f2b3bf1e0b562a2c74e353d2e03f2f50ef from qemu
Let users of qemu_get_ram_ptr and qemu_ram_ptr_length pass in an
address that is relative to the MemoryRegion. This basically means
what address_space_translate returns.
Because the semantics of the second parameter change, rename the
function to qemu_map_ram_ptr.
Backports commit 0878d0e11ba8013dd759c6921cbf05ba6a41bd71 from qemu
Move the old qemu_ram_addr_from_host to memory_region_from_host and
make it return an offset within the region. For qemu_ram_addr_from_host
return the ram_addr_t directly, similar to what it was before
commit 1b5ec23 ("memory: return MemoryRegion from qemu_ram_addr_from_host",
2013-07-04).
Backports commit 07bdaa4196b51bc7ffa7c3f74e9e4a9dc8a7966a from qemu
Of the two callers, one does not use it, and the other can compute
it itself based on the other output argument (offset) and the RAMBlock.
Backports commit f615f39616c4fd1a3a3b078af8d75bb4be6390de from qemu
Remove direct uses of ram_addr_t and optimize memory_region_{get,set}_fd
now that a MemoryRegion knows its RAMBlock directly.
Backports commit 4ff87573df3606856a92c14eef3393a63d736d11 from qemu
The collision check does nothing and hasn't been used. Remove the
variable together with related code.
Backports commit b61359781958759317ee6fd1a45b59be0b7dbbe1 from qemu
On the one hand, we have already qemu_get_ram_block() whose function
is similar. On the other hand, we can directly use mr->ram_block but
searching RAMblock by ram_addr which is a kind of waste.
Backports commit fa53a0e53efdc7002497ea4a76aacf6cceb170ef from qemu
pio_addr_t is almost unused, because these days I/O ports are simply
accessed through the address space. cpu_{in,out}[bwl] themselves are
almost unused; monitor.c and xen-hvm.c could use address_space_read/write
directly, since they have an integer size at hand. This leaves qtest as
the only user of those functions.
On the other hand even portio_* functions use this type; the only
interesting use of pio_addr_t thus is include/hw/sysbus.h. I guess I
could move it there, but I don't see much benefit in that either. Using
uint32_t is enough and avoids the need to include ioport.h everywhere.
Backports commit 89a80e7400f7225d9401b35ef32454b4ab29dc67 from qemu
exec-all.h contains TCG-specific definitions. It is not needed outside
TCG-specific files such as translate.c, exec.c or *helper.c.
One generic function had snuck into include/exec/exec-all.h; move it to
include/qom/cpu.h.
Backports commit 63c915526d6a54a95919ebece83fa9ca631b2508 from qemu
TCG backends do not need most of exec-all.h; extract what they actually
need to a separate file or move it directly to tcg.h. The next patch
will stop including exec-all.h from everywhere.
Backports commit 00f6da6a1a5d1ce085334eccbb50ec899ceed513 from qemu
Disentangle cpu-common.h and memory.h from NEED_CPU_H. Prototypes are
not defined for !NEED_CPU_H, so remove them from poison.h too. Only
macros need poisoning.
Backports commit a7d6039cb35592683ecc56d2b37817da2d2f8b00 from qemu
'tb_invalidated_flag' was meant to catch two events:
* some TB has been invalidated by tb_phys_invalidate();
* the whole translation buffer has been flushed by tb_flush().
Then it was checked:
* in cpu_exec() to ensure that the last executed TB can be safely
linked to directly call the next one;
* in cpu_exec_nocache() to decide if the original TB should be provided
for further possible invalidation along with the temporarily
generated TB.
It is always safe to patch an invalidated TB since it is not going to be
used anyway. It is also safe to call tb_phys_invalidate() for an already
invalidated TB. Thus, setting this flag in tb_phys_invalidate() is
simply unnecessary. Moreover, it can prevent from pretty proper linking
of TBs, if any arbitrary TB has been invalidated. So just don't touch it
in tb_phys_invalidate().
If this flag is only used to catch whether tb_flush() has been called
then rename it to 'tb_flushed'. Declare it as 'bool' and stick to using
only 'true' and 'false' to set its value. Also, instead of setting it in
tb_gen_code(), just after tb_flush() has been called, do it right inside
of tb_flush().
In cpu_exec(), this flag is used to track if tb_flush() has been called
and have made 'next_tb' (a reference to the last executed TB) invalid
for linking it to directly call the next TB. tb_flush() can be called
during the CPU execution loop from tb_gen_code(), during TB execution or
by another thread while 'tb_lock' is released. Catch for translation
buffer flush reliably by resetting this flag once before first TB lookup
and each time we find it set before trying to add a direct jump. Don't
touch in in tb_find_physical().
Each vCPU has its own execution loop in multithreaded mode and thus
should have its own copy of the flag to be able to reset it with its own
'next_tb' and don't affect any other vCPU execution thread. So make this
flag per-vCPU and move it to CPUState.
In cpu_exec_nocache(), we only need to check if tb_flush() has been
called from tb_gen_code() called by cpu_exec_nocache() itself. To do
this reliably, preserve the old value of the flag, reset it before
calling tb_gen_code(), check afterwards, and combine the saved value
back to the flag.
This patch is based on the patch "tcg: move tb_invalidated_flag to
CPUState" from Paolo Bonzini <pbonzini@redhat.com>.
Backports commit 6f789be56d3f38e9214dafcfab3bf9be7191f370 from qemu
The check is to make sure that another thread hasn't already done the
same while we were outside of tb_lock. Mention this in a comment.
Backports commit 9962c478b153a18fe88a6509fe58cd178aff8abc from qemu
These fields do not contain pure pointers to a TranslationBlock
structure. So uintptr_t is the most appropriate type for them.
Also put some asserts to assure that the two least significant bits of
the pointer are always zero before assigning it to jmp_list_first.
Backports commit c37e6d7e3589ecb96914faa21025ad7ba6654aea from qemu
Briefly describe in a comment how direct block chaining is done. It
should help in understanding of the following data fields.
Rename some fields in TranslationBlock and TCGContext structures to
better reflect their purpose (dropping excessive 'tb_' prefix in
TranslationBlock but keeping it in TCGContext):
tb_next_offset => jmp_reset_offset
tb_jmp_offset => jmp_insn_offset
tb_next => jmp_target_addr
jmp_next => jmp_list_next
jmp_first => jmp_list_first
Avoid using a magic constant as an invalid offset which is used to
indicate that there's no n-th jump generated.
Backports commit f309101c26b59641fc1aa8fb2a98a5441cdaea03 from qemu
Ensure direct jump patching in ARM is atomic by using
atomic_read()/atomic_set() for code patching.
Backports commit 7d14e0e2d661479985197203589c38840e1066df from qemu
Ensure direct jump patching in s390 is atomic by:
* naturally aligning a location of direct jump address;
* using atomic_read()/atomic_set() for code patching.
Backports commit ed3d51ecd7fe248d3959e469d53890ac9ffe0cd2 from qemu
Ensure direct jump patching in i386 is atomic by:
* naturally aligning a location of direct jump address;
* using atomic_read()/atomic_set() for code patching.
Backports commit 0d07abf05e98903c7faf204a9a90f7d45b7554dc from qemu
We are inconsistent with the type of tb->flags: usage varies loosely
between int and uint64_t. Settle to uint32_t everywhere, which is
superior to both: at least one target (aarch64) uses the most significant
bit in the u32, and uint64_t is wasteful.
Compile-tested for all targets.
Backports commit 89fee74a0f066dfd73830a7b5fa137e87888c870 from qemu
Use tcg_set_insn_param() instead of directly accessing internal
tcg data structures to update an insn param.
Backports commit 25caa94c4a26daaab1e65c6d887e2972aeb5749e from qemu
Move the architecture agnostic function prototypes for exec.c out of
cputlb.h to exec-all.h. This allows hiding of the arch specific
cputlb.h from exec.c which should be getting close to having no
architecture specifics. Prepares support for multi-arch, which will have
a minimal cpu.h that services exec.c but not cputlb.h.
Backports commit dfccc7602374c9fd3b083208b552d62daa244811 from qemu
To prepare for multi-arch, cputlb.c should only have awareness of one
single architecture. This means it should not have access to the full
CPU lists which may be heterogeneous. Instead, push the CPU_LOOP() up
to the one and only caller in exec.c.
Backports commit 9a13565d52bfd321934fb44ee004bbaf5f5913a8 from qemu
The last two arguments to these functions are the last and first bit to
check relative to the base. The code was using incorrectly the first
bit and the number of bits. Fix this in cpu_physical_memory_get_dirty
and cpu_physical_memory_all_dirty. This requires a few changes in the
iteration; change the code in cpu_physical_memory_set_dirty_range to
match.
Backports commit 88c73d16ad1b6c22a2ab082064d0d521f756296a from qemu
Although accesses to ram_list.dirty_memory[] use atomics so multiple
threads can safely dirty the bitmap, the data structure is not fully
thread-safe yet.
This patch handles the RAM hotplug case where ram_list.dirty_memory[] is
grown. ram_list.dirty_memory[] is change from a regular bitmap to an
RCU array of pointers to fixed-size bitmap blocks. Threads can continue
accessing bitmap blocks while the array is being extended. See the
comments in the code for an in-depth explanation of struct
DirtyMemoryBlocks.
I have tested that live migration with virtio-blk dataplane works.
Backports commit 5b82b703b69acc67b78b98a5efc897a3912719eb from qemu
qemu-log: dfilter-ise exec, out_asm, op and opt_op
This ensures the code generation debug code will honour -dfilter if set.
For the "exec" tracing I've added a new inline macro for efficiency's
sake.
Backports commit d977e1c2dbc9e63454b2000f91954d02543bf43b from qemu
Improve the TB execution logging so that it is easier to identify
what is happening from trace logs:
* move the "Trace" logging of executed TBs into cpu_tb_exec()
so that it is emitted if and only if we actually execute a TB,
and for consistency for the CPU state logging
* log when we link two TBs together via tb_add_jump()
* log when cpu_tb_exec() returns early from a chain of TBs
The new style logging looks like this:
Trace 0x7fb7cc822ca0 [ffffffc0000dce00]
Linking TBs 0x7fb7cc822ca0 [ffffffc0000dce00] index 0 -> 0x7fb7cc823110 [ffffffc0000dce10]
Trace 0x7fb7cc823110 [ffffffc0000dce10]
Trace 0x7fb7cc823420 [ffffffc000302688]
Trace 0x7fb7cc8234a0 [ffffffc000302698]
Trace 0x7fb7cc823520 [ffffffc0003026a4]
Trace 0x7fb7cc823560 [ffffffc0000dce44]
Linking TBs 0x7fb7cc823560 [ffffffc0000dce44] index 1 -> 0x7fb7cc8235d0 [ffffffc0000dce70]
Trace 0x7fb7cc8235d0 [ffffffc0000dce70]
Stopped execution of TB chain before 0x7fb7cc8235d0 [ffffffc0000dce70]
Trace 0x7fb7cc8235d0 [ffffffc0000dce70]
Trace 0x7fb7cc822fd0 [ffffffc0000dd52c]
Backports commit 1a830635229e14c403600167823ea6b3b79d3097 from qemu
Just specifying ops = NULL in some cases can be more convenient than having
two functions.
Backports commit 6d6d2abf2c2e52c0f404d0a31a963e945b0cc7ad from qemu
All references to mr->ram_addr are replaced by
memory_region_get_ram_addr(mr) (except for a few assertions that are
replaced with mr->ram_block).
Backports commit 8e41fb63c5bf29ecabe0cee1239bf6230f19978a from qemu
Previously we return RAMBlock.offset; now return the pointer to the
whole structure.
ram_block_add returns void now, error is completely passed with errp.
Backports commit 528f46af6ecd1e300db18684969104d4067b867b from qemu
these two functions consume too much cpu overhead to
find the RAMBlock by ram address.
After this patch, we can pass the RAMBlock pointer
to them so that they don't need to find the RAMBlock
anymore most of the time. We can get better performance
in address translation processing.
Backports commit 3655cb9c7375a595a8051ec677c515b24d5c1fe6 from qemu
Each RAM memory region has a unique corresponding RAMBlock.
In the current realization, the memory region only stored
the ram_addr which means the offset of RAM address space,
We need to qurey the global ram.list to find the ram block
by ram_addr if we want to get the ram block, which is very
expensive.
Now, we store the RAMBlock pointer into memory region
structure. So, if we know the mr, we can easily get the
RAMBlock.
Backports commit 58eaa2174e99d9a05172d03fd2799ab8fd9e6f60 from qemu
This condition is true in the common case, so we can cut out the body of
the function. In addition, this makes it easier for the compiler to do
at least partial inlining, even if it decides that fully inlining the
function is unreasonable.
Backports commit 8bafcb21643a39a5b29109f8bd5ee5a6f0f6850b from qemu
check the return value of the function it calls and error if it's non-0
Fixup qemu_rdma_init_one_block that is the only current caller,
and rdma_add_block the only function it calls using it.
Pass the name of the ramblock to the function; helps in debugging.
Backports commit e3807054e20fb3b94d18cb751c437ee2f43b6fac from qemu
This will either create a new AS or return a pointer to an
already existing equivalent one, if we have already created
an AS for the specified root memory region.
The motivation is to reuse address spaces as much as possible.
It's going to be quite common that bus masters out in device land
have pointers to the same memory region for their mastering yet
each will need to create its own address space. Let the memory
API implement sharing for them.
Aside from the perf optimisations, this should reduce the amount
of redundant output on info mtree as well.
Thee returned value will be malloced, but the malloc will be
automatically freed when the AS runs out of refs.
Backports commit f0c02d15b57da6f5463e3768aa0cfeedccf4b8f4 from qemu
Add a function to return the AddressSpace for a CPU based on
its numerical index. (Callers outside exec.c don't have access
to the CPUAddressSpace struct so can't just fish it out of the
CPUState struct directly.)
Backports commit 651a5bc03705102de519ebf079a40ecc1da991db from qemu
Pass the MemTxAttrs for the memory access to iotlb_to_region(); this
allows it to determine the correct AddressSpace to use for the lookup.
Backports commit a54c87b68a0410d0cf6f8b84e42074a5cf463732 from qemu
When looking up the MemoryRegionSection for the new TLB entry in
tlb_set_page_with_attrs(), use cpu_asidx_from_attrs() to determine
the correct address space index for the lookup, and pass it into
address_space_translate_for_iotlb().
Backports commit d7898cda81b6efa6b2d7a749882695cdcf280eaa from qemu
Allow multiple calls to cpu_address_space_init(); each
call adds an entry to the cpu->ases array at the specified
index. It is up to the target-specific CPU code to actually use
these extra address spaces.
Since this multiple AddressSpace support won't work with
KVM, add an assertion to avoid confusing failures.
Backports commit 12ebc9a76dd7702aef0a3618717a826c19c34ef4 from qemu
Rather than setting cpu->as unconditionally in cpu_exec_init
(and then having target-i386 override this later), don't set
it until the first call to cpu_address_space_init.
This requires us to initialise the address space for
both TCG and KVM (KVM doesn't need the AS listener but
it does require cpu->as to be set).
For target CPUs which don't set up any address spaces (currently
everything except i386), add the default address_space_memory
in qemu_init_vcpu().
Backports commit 56943e8cc14b7eeeab67d1942fa5d8bcafe3e53f from qemu
memcpy can take a large amount of time for small reads and writes.
Handle the common case of reading s/g descriptors from memory (there
is no corresponding "write" case that is as common, because writes
often use address_space_st* functions) by inlining the relevant
parts of address_space_read into the caller.
Backports commit 3cc8f884996584630734a90c9b3c535af81e3c92 from qemu
We want to inline the case where there is only one iteration, because
then the compiler can also inline the memcpy. As a start, extract
everything after the first address_space_translate call.
Backports commit a203ac702e0720135fac8b1f2061d119814c1798 from qemu
For the common case of DMA into non-hotplugged RAM, it is unnecessary
but expensive to do object_ref/unref. Add back an owner field to
MemoryRegion, so that these memory regions can skip the reference
counting.
Backports commit 612263cf33062f7441a5d0e3b37c65991fdc3210 from qemu
Order fields so that all fields accessed during a RAM read/write fit in
the same cache line.
Backports commit a676854f3447019c7c4b005ab6aece905fccfddd from qemu
Replace qemu_ram_free_from_ptr() with qemu_ram_free().
The only difference between qemu_ram_free_from_ptr() and
qemu_ram_free() is that g_free_rcu() is used instead of
call_rcu(reclaim_ramblock). We can safely replace it because:
* RAM blocks allocated by qemu_ram_alloc_from_ptr() always have
RAM_PREALLOC set;
* reclaim_ramblock(block) will do nothing except g_free(block)
if RAM_PREALLOC is set at block->flags.
Backports commit a29ac16632aec6065c72985b9f7eeb1ca6fbef4a from qemu
Add a function to find a RAMBlock by name; use it in two
of the places that already open code that loop; we've
got another use later in postcopy.
Backports commit e3dd74934f2d2c8c67083995928ff68e8c1d0030 from qemu
Postcopy sends RAMBlock names and offsets over the wire (since it can't
rely on the order of ramaddr being the same), and it starts out with
HVA fault addresses from the kernel.
qemu_ram_block_from_host translates a HVA into a RAMBlock, an offset
in the RAMBlock and the global ram_addr_t value.
Rewrite qemu_ram_addr_from_host to use qemu_ram_block_from_host.
Provide qemu_ram_get_idstr since its the actual name text sent on the
wire.
Backports commit 422148d3e56c3c9a07c0cf36c1e0a0b76f09c357 from qemu
This makes ROM blocks resizeable. This infrastructure is required for other
functionality we have queued.
Backports commit aaf03019175949eda5087329448b8a0033b89479 from qemu
At present, the "average" guestimate of TB size is way too small, leading
to many unused entries in the pre-allocated TB array. For a guest with 1GB
ram, we're currently allocating 256MB for the array.
Survey arm, alpha, aarch64, ppc, sparc, i686, x86_64 guests running on
x86_64 and ppc64 hosts and select a new average. The size of the array
drops to 81MB with no more flushing than before.
Backports commit 126d89e8cdfa3be15d51f76906eaccbcd0023f98 from qemu
We currently pre-compute an worst case code size for any TB, which
works out to be 122kB. Since the average TB size is near 1kB, this
wastes quite a lot of storage.
Instead, check for overflow in between generating code for each opcode.
The overhead of the check isn't measurable and wastage is minimized.
Backports commit b125f9dc7bd68cd4c57189db4da83b0620b28a72 from qemu
It is no longer used, so tidy up everything reached by it.
This includes the gen_opc_* arrays, the search_pc parameter
and the inline gen_intermediate_code_internal functions.
Backports commit 4e5e1215156662b2b153255c49d4640d82c5568b from qemu
In this case, QEMU might longjmp out of cpu-exec.c and miss the final
cleanup in cpu_exec_nocache. Do this manually through a new compile
flag.
Backports commit d8a499f17ee5f05407874f29f69f0e3e3198a853 from qemu
The gen_opc_* arrays are already redundant with the data stored in
the insn_start arguments. Transition restore_state_to_opc to use
data from the latter.
Backports commit bad729e272387de7dbfa3ec4319036552fc6c107 from qemu
Change tlb_set_dirty() to accept a CPU instead of an env pointer. This
allows for removal of another CPUArchState usage from prototypes that
need to be QOMified.
Backports commit bcae01e468d961ad9afaf4148329147e4be209ab from qemu
There is some iffy lock hierarchy going on in translate-all.c. To
fix it, we need to take the mmap_lock in cpu-exec.c. Make the
functions globally available.
Backports commit 8fd19e6cfd5b6cdf028c6ac2ff4157ed831ea3a6 from qemu
This patch introduces loop exit function, which also
restores guest CPU state according to the value of host
program counter.
Backports commit 1c3c8af1fb40a481c07749e0448644d9b7700415 from qemu
Now that the cpu_ld/st_* function directly call helper_ret_ld/st, we can
drop the old helper_ld/st functions.
Backports commit b8611499b940b1b4db67aa985e3a844437bcbf00 from qemu
This patch introduces several helpers to pass return address
which points to the TB. Correct return address allows correct
restoring of the guest PC and icount. These functions should be used when
helpers embedded into TB invoke memory operations.
Backports commit 282dffc8a4bfe8724548cabb8a26698bde0a6e18 from qemu
This is set to true when the index is for an instruction fetch
translation.
The core get_page_addr_code() sets it, as do the SOFTMMU_CODE_ACCESS
acessors.
All targets ignore it for now, and all other callers pass "false".
This will allow targets who wish to split the mmu index between
instruction and data accesses to do so. A subsequent patch will
do just that for PowerPC.
Backports commit 97ed5ccdee95f0b98bedc601ff979e368583472c from qemu
Guest CPU TLB maintenance operations may be sufficiently
specialized to only need to flush TLB entries corresponding
to a particular MMU index. Implement cputlb functions for
this, to avoid the inefficiency of flushing TLB entries
which we don't need to.
Backports commit d7a74a9d4a68e27b3a8ceda17bb95cb0a23d8e4d from qemu
There was a complicated subtractive arithmetic for determining the
padding on the CPUTLBEntry structure. Simplify this with a union.
Backports commit b4a4b8d0e0767c85946fd8fc404643bf5766351a from qemu
The callers (most of them in target-foo/cpu.c) to this function all
have the cpu pointer handy. Just pass it to avoid an ENV_GET_CPU() from
core code (in exec.c).
Backports commit 4bad9e392e788a218967167a38ce2ae7a32a6231 from qemu
All of the core-code usages of this API have the cpu pointer handy so
pass it in. There are only 3 architecture specific usages (2 of which
are commented out) which can just use ENV_GET_CPU() locally to get the
cpu pointer. The reduces core code usage of the CPU env, which brings
us closer to common-obj'ing these core files.
Backports commit bbd77c180d7ff1b04a7661bb878939b2e1d23798 from qemu
Currently the "host" page size alignment API is really aligning to both
host and target page sizes. There is the qemu_real_page_size which can
be used for the actual host page size but it's missing a mask and ALIGN
macro as provided for qemu_page_size. Complete the API. This allows
system level code that cares about the host page size to use a
consistent alignment interface without having to un-needingly align to
the target page size. This also reduces system level code dependency
on the cpu specific TARGET_PAGE_SIZE.
Backports commit 4e51361d79289aee2985dfed472f8d87bd53a8df from qemu
Including qemu-common.h from other header files is generally a bad
idea, because it means it's very easy to end up with a circular
dependency. For instance, if we wanted to include memory.h from
qom/cpu.h we'd end up with this loop:
memory.h -> qemu-common.h -> cpu.h -> cpu-qom.h -> qom/cpu.h -> memory.h
Remove the include from memory.h. This requires us to fix up a few
other files which were inadvertently getting declarations indirectly
through memory.h.
The biggest change is splitting the fprintf_function typedef out
into its own header so other headers can get at it without having
to include qemu-common.h.
Backports commit fba0a593b2809ecdda68650952cf3d3332ac1990 from qemu
This introduces the memory region property "global_locking". It is true
by default. By setting it to false, a device model can request BQL-free
dispatching of region accesses to its r/w handlers. The actual BQL
break-up will be provided in a separate patch.
Backports commit 196ea13104f802c508e57180b2a0d2b3418989a3 from qemu
These are not Architecture specific in any way so move them out of
cpu-defs.h. tb-hash.h is an appropriate place as a leading user and
their strong relationship to TB hashing and caching.
Backports commit 41da4bd6420afd1209c408974920f63ff9c658e1 from qemu
This is one of very few things in exec-all with a genuine CPU
architecture dependency. Move these hashing helpers to a new
header to trim exec-all.h down to a near architecture-agnostic
header.
The defs are only used by cpu-exec and translate-all which are both
arch-obj's so the new tb-hash.h has no core code usage.
Backports commit e1b89321bafea9fb33d87852fc91fee579d17dfe from qemu