The memory writes done to push registers on the stack
on exception entry in M profile CPUs are supposed to
go via MPU permissions checks, which may cause us to
take a derived exception instead of the original one of
the MPU lookup fails. We were implementing these as
always-succeeds direct writes to physical memory.
Rewrite v7m_push_stack() to do the necessary checks.
Backports commit fd592d890ec40e3686760de84044230a8ebb1eb3 from qemu
In the v8M architecture, if the process of taking an exception
results in a further exception this is called a derived exception
(for example, an MPU exception when writing the exception frame to
memory). If the derived exception happens while pushing the initial
stack frame, we must ignore any subsequent possible exception
pushing the callee-saves registers.
In preparation for making the stack writes check for exceptions,
add a return value from v7m_push_stack() and a new parameter to
v7m_exception_taken(), so that the former can tell the latter that
it needs to ignore failures to write to the stack. We also plumb
the argument through to v7m_push_callee_stack(), which is where
the code to ignore the failures will be.
(Note that the v8M ARM pseudocode structures this slightly differently:
derived exceptions cause the attempt to process the original
exception to be abandoned; then at the top level it calls
DerivedLateArrival to prioritize the derived exception and call
TakeException from there. We choose to let the NVIC do the prioritization
and continue forward with a call to TakeException which will then
take either the original or the derived exception. The effect is
the same, but this structure works better for QEMU because we don't
have a convenient top level place to do the abandon-and-retry logic.)
Backports commit 0094ca70e165cfb69882fa2e100d935d45f1c983 from qemu
Currently armv7m_nvic_acknowledge_irq() does three things:
* make the current highest priority pending interrupt active
* return a bool indicating whether that interrupt is targeting
Secure or NonSecure state
* implicitly tell the caller which is the highest priority
pending interrupt by setting env->v7m.exception
We need to split these jobs, because v7m_exception_taken()
needs to know whether the pending interrupt targets Secure so
it can choose to stack callee-saves registers or not, but it
must not make the interrupt active until after it has done
that stacking, in case the stacking causes a derived exception.
Similarly, it needs to know the number of the pending interrupt
so it can read the correct vector table entry before the
interrupt is made active, because vector table reads might
also cause a derived exception.
Create a new armv7m_nvic_get_pending_irq_info() function which simply
returns information about the highest priority pending interrupt, and
use it to rearrange the v7m_exception_taken() code so we don't
acknowledge the exception until we've done all the things which could
possibly cause a derived exception.
Backports part of commit 6c9485188170e11ad31ce477c8ce200b8e8ce59d from qemu
In order to support derived exceptions (exceptions generated in
the course of trying to take an exception), we need to be able
to handle prioritizing whether to take the original exception
or the derived exception.
We do this by introducing a new function
armv7m_nvic_set_pending_derived() which the exception-taking code in
helper.c will call when a derived exception occurs. Derived
exceptions are dealt with mostly like normal pending exceptions, so
we share the implementation with the armv7m_nvic_set_pending()
function.
Note that the way we structure this is significantly different
from the v8M Arm ARM pseudocode: that does all the prioritization
logic in the DerivedLateArrival() function, whereas we choose to
let the existing "identify highest priority exception" logic
do the prioritization for us. The effect is the same, though.
Backports part of commit 5ede82b8ccb652382c106d53f656ed67997d76e8 from qemu
The x86 vector instruction set is extremely irregular. With newer
editions, Intel has filled in some of the blanks. However, we don't
get many 64-bit operations until SSE4.2, introduced in 2009.
The subsequent edition was for AVX1, introduced in 2011, which added
three-operand addressing, and adjusts how all instructions should be
encoded.
Given the relatively narrow 2 year window between possible to support
and desirable to support, and to vastly simplify code maintainence,
I am only planning to support AVX1 and later cpus.
Backports commit 770c2fc7bb70804ae9869995fd02dadd6d7656ac from qemu
Trivial move and constant propagation. Some identity and constant
function folding, but nothing that requires knowledge of the size
of the vector element.
Backports commit 170ba88f45bd7b1c5593021ed8e174f663b0bd1a from qemu
Use dup to convert a non-constant scalar to a third vector.
Add addition, multiplication, and logical operations with an immediate.
Add addition, subtraction, multiplication, and logical operations with
a non-constant scalar. Allow for the front-end to build operations in
which the scalar operand comes first.
Backports commit 22fc3527034678489ec554e82fd52f8a7f05418e from qemu
No vector ops as yet. SSE only has direct support for 8- and 16-bit
saturation; handling 32- and 64-bit saturation is much more expensive.
Backports commit f49b12c6e6a75a5bd109bcbbda072b24e5fb8dfd from qemu
Opcodes are added for scalar and vector shifts, but considering the
varied semantics of these do not expose them to the front ends. Do
go ahead and provide them in case they are needed for backend expansion.
Backports commit d0ec97967f940bbc11dced83422b39c224127f1e from qemu
Some functions use intN_t arguments, some use uintN_t, some just
used "unsigned". To aid putting function pointers in tables, we
need consistency.
Backports commit 474b2e8f0f765515515b495e6872b5e18a660baf from qemu
Typical slowdown introduced by AddressSanitizer is 2x.
UBSan shouldn't have much impact on runtime cost.
Enable it by default when --enable-debug, unless --disable-sanitizers.
Backports commit 247724cb302af5d70c8853154b640dfabf2bbb56 from qemu
Python2 did not validate locale correctness when reading input data, so
would happily read UTF-8 data in non-UTF-8 locales. Python3 is strict so
if you try to read UTF-8 data in the C locale, it will raise an error
for any UTF-8 bytes that aren't representable in 7-bit ascii encoding.
e.g.
UnicodeDecodeError: 'ascii' codec can't decode byte 0xc3 in position 54: ordinal not in range(128)
Traceback (most recent call last):
File "/tmp/qemu-test/src/scripts/qapi-commands.py", line 317, in <module>
schema = QAPISchema(input_file)
File "/tmp/qemu-test/src/scripts/qapi.py", line 1468, in __init__
parser = QAPISchemaParser(open(fname, 'r'))
File "/tmp/qemu-test/src/scripts/qapi.py", line 301, in __init__
previously_included)
File "/tmp/qemu-test/src/scripts/qapi.py", line 348, in _include
exprs_include = QAPISchemaParser(fobj, previously_included, info)
File "/tmp/qemu-test/src/scripts/qapi.py", line 271, in __init__
self.src = fp.read()
File "/usr/lib64/python3.5/encodings/ascii.py", line 26, in decode
return codecs.ascii_decode(input, self.errors)[0]
More background on this can be seen in
https://www.python.org/dev/peps/pep-0538/
Many distros support a new C.UTF-8 locale that is like the C locale,
but with UTF-8 instead of 7-bit ASCII. That is not entirely portable
though. This patch thus sets the LANG to "C", but overrides LC_CTYPE
to be en_US.UTF-8 locale. This gets us pretty close to C.UTF-8, but
in a way that should be portable to everywhere QEMU builds.
This patch only forces UTF-8 for QAPI scripts, since that is the one
showing the immediate error under Python3 with C locale, but potentially
we ought to force this for all python scripts used in the build process.
Backports commit d4e5ec877ca698a87dabe68814c6f93668f50c60 from qemu
Some early python 3.x versions will have different default
ordering when calling the 'values()' method on a dict, compared
to python 2.x and later 3.x versions. Explicitly sort the items
to get a stable ordering.
Backports commit f7a5376d4b667cf6c83c1d640e32d22456d7b5ee from qemu
The OrderedDict class appeared in the 'collections' module
from python 2.7 onwards, so use that in preference to our
local backport if available.
Backports commit 38710a8994911d98acbe183a39ec3a53638de510 from qemu
The iteritems()/itervalues() methods are gone in py3, but the
items()/values() methods are still around. The latter are less
efficient than the former in py2, but this has unmeasurably
small impact on QEMU build time, so taking portability over
efficiency is a net win.
Backports commit 2f8480447067d6f42af52a886385284ead052af9 from qemu
Python 3 no longer supports the bare "print" statement, it must be
called as a normal function with round brackets. It is possible to
opt-in to this new syntax with Python 2.6 onwards by importing the
"print_function" from the "__future__" module, making it easy to
support Python 2 and 3 in parallel.
Backports commit ef9d9108917d6d5f903bca31602827e512a51c50 from qemu
The instruction "moves" can select source and destination
address space (user or kernel). This patch modifies
all the load/store functions to be able to provide
the address space the caller wants to use instead
of using the current one. All the callers are modified
to provide the default address space to these functions.
Backports commit 54e1e0b5b5ce4fc76335b1fbbf09cb8fdd5ab89d from qemu
Only add MC68040 MMU page table processing and related
registers (Special Status Word, Translation Control Register,
User Root Pointer and Supervisor Root Pointer).
Transparent Translation Registers, DFC/SFC and pflush/ptest
will be added later.
Backports commit 88b2fef6c3c3b45ac0dc2196ace7248a09c8e41d from qemu
The MC68040 MMU provides the size of the access that
triggers the page fault.
This size is set in the Special Status Word which
is written in the stack frame of the access fault
exception.
So we need the size in m68k_cpu_unassigned_access() and
m68k_cpu_handle_mmu_fault().
To be able to do that, this patch modifies the prototype of
handle_mmu_fault handler, tlb_fill() and probe_write().
do_unassigned_access() already includes a size parameter.
This patch also updates handle_mmu_fault handlers and
tlb_fill() of all targets (only parameter, no code change).
Backports commit 98670d47cd8d63a529ff230fd39ddaa186156f8c from qemu
Rather than passing a regno to the helper, pass pointers to the
vector register directly. This eliminates the need to pass in
the environment pointer and reduces the number of places that
directly access env->vfp.regs[].
Backports commit e7c06c4e4c98c47899417f154df1f2ef4e8d09a0 from qemu
Rather than passing regnos to the helpers, pass pointers to the
vector registers directly. This eliminates the need to pass in
the environment pointer and reduces the number of places that
directly access env->vfp.regs[].
Backports commit b13708bbbdda54c7f7e28222b22453986c026391 from qemu
Rather than passing regnos to the helpers, pass pointers to the
vector registers directly. This eliminates the need to pass in
the environment pointer and reduces the number of places that
directly access env->vfp.regs[].
Backports commit 1a66ac61af45af04688d1d15896737310e366c06 from qemu
Commit ("3b39d734141a target/arm: Handle page table walk load failures
correctly") modified both versions of the page table walking code (i.e.,
arm_ldl_ptw and arm_ldq_ptw) to record the result of the translation in
a temporary 'data' variable so that it can be inspected before being
returned. However, arm_ldq_ptw() returns an uint64_t, and using a
temporary uint32_t variable truncates the upper bits, corrupting the
result. This causes problems when using more than 4 GB of memory in
a TCG guest. So use a uint64_t instead.
Backports commit 9aea1ea31af25fe344a88da086ff913cca09c667 from qemu
The code sequence we were generating was only good for unsigned
comparisons. For signed comparisions, use the sequence from gcc.
Fixes booting of ppc64 firmware, with a patch changing the code
sequence for ppc comparisons.
Backports commit 7170ac33135e6ecf89752d3949bcecf9b9766d1c from qemu
It is more typical to provide the ';' by the caller of a macro
than to embed it in the macro itself; this is because syntax
highlight engines can get confused if a macro is called without
a semicolon before the closing '}'.
Backports commit 94f5c480e9b5ce95394026b3f025816470e23eaf from qemu
Move generic make flags in MAKEFLAGS (SUBDIR_MAKEFLAGS is more qemu specific).
Use --quiet to silence make 'is up to date' message.
Backports commit 42a77f1ce4934b243df003f95bda88530631387a from qemu
Instead of ignoring the response from address_space_ld*()
(indicating an attempt to read a page table descriptor from
an invalid physical address), use it to report the failure
correctly.
Since this is another couple of locations where we need to
decide the value of the ARMMMUFaultInfo ea bit based on a
MemTxResult, we factor out that operation into a helper
function.
Backports commit 3b39d734141a71296d08af3d4c32f872fafd782e from qemu
For PMSAv7, the v7A/R Arm ARM defines that setting AP to 0b111
is an UNPREDICTABLE reserved combination. However, for v7M
this value is documented as having the same behaviour as 0b110:
read-only for both privileged and unprivileged. Accept this
value on an M profile core rather than treating it as a guest
error and a no-access page.
Backports commit 8638f1ad7403b63db880dadce38e6690b5d82b64 from qemu
Refactor disas_thumb2_insn() so that it generates the code for raising
an UNDEF exception for invalid insns, rather than returning a flag
which the caller must check to see if it needs to generate the UNDEF
code. This brings the function in to line with the behaviour of
disas_thumb_insn() and disas_arm_insn().
Backports commit 2eea841c11096e8dcc457b80e21f3fbdc32d2590 from qemu
ldxp loads two consecutive doublewords from memory regardless of CPU
endianness. On store, stlxp currently assumes to work with a 128bit
value and consequently switches order in big-endian mode. With this
change it packs the doublewords in reverse order in anticipation of the
128bit big-endian store operation interposing them so they end up in
memory in the right order. This makes it work for both MTTCG and !MTTCG.
It effectively implements the ARM ARM STLXP operation pseudo-code:
data = if BigEndian() then el1:el2 else el2:el1;
With this change an aarch64_be Linux 4.14.4 kernel succeeds to boot up
in system emulation mode.
Backports commit 0785557f8811133bd69be02aeccf018d47a26373 from qemu
This code is preventing the MMU debug code from displaying virtual
mappings of IO devices (anything that is not located in the RAM).
Before this patch, Qemu would output 0xffffffffffffffff (-1) as the
physical address corresponding to an IO device virtual address.
With this patch the intended physical address is displayed.
Backports commit 7e450a8f50ac12fc8f69b6ce555254c84efcf407 from qemu
Add the third stack pointer, the Interrupt Stack Pointer (ISP)
(680x0 only). This stack will be needed in softmmu mode.
Update movec to set/get the value of the three stacks.
Backports commit 6e22b28e22aa6ed1b8db6f24da2633868019d4c9 from qemu
Some cleanup, and allows SR to be moved from any addressing mode.
Previous code was wrong for coldfire: coldfire also allows to
use addressing mode to set SR/CCR. It only supports Data register
to get SR/CCR (move from)
Backports commit b6a21d8d8f69ac04fd6180e752a65d582c07e948 from qemu
The instruction traps if the CPU is not in
Supervisor state but the helper is empty because
there is no easy way to reset all the peripherals
without resetting the CPU itself.
Backports commit 0bdb2b3bf5660f892ddbfa09baea56cdca57ad1d from qemu
Add cache lines invalidate and cache lines push
as no-op operations, as we don't have cache.
These instructions are 68040 only.
Backports commit f58ed1c50add3e76331afdc92387c0da9dd9e443 from qemu
move16 moves the source line to the destination line. Lines are aligned
to 16-byte boundaries and are 16 bytes long.
Backports commit 9d4f0429f3dc1dc6c67de3eaa3106e6c1cfa1524 from qemu
chk and chk2 compare a value to boundaries, and
trigger a CHK exception if the value is out of bounds.
Backports commit 8bf6cbaf396a8b54b138bb8a7c3377f2868ed16e from qemu
As gen_helper_get_ccr() is able to compute CCR from cc_op and
flags, we don't need to flush flags before to call it.
flush_flags() and get_ccr() use COMPUTE_CCR() to compute
flags. get_ccr() computes CCR value,
whereas flush_flags update live cc_op and flags.
Backports commit 4131c242cc850aaf76e59d4c787d220f07850cf5 from qemu
And remove update_cc_op() from gen_exception() because there is
one in gen_jmp_im().
Backports commit 7cd7b5ca9be805e8a4ced4c07014c24e34812f27 from qemu
We had two fields specific to INDEX_op_call. Rename these and
add some macros so that the fields may be reused for other opcodes.
Backports commit cd9090aa9dbba30db8aec9a2fc103aaf1ab0f5a7 from qemu
With no fixed array allocation, we can't overflow a buffer.
This will be important as optimizations related to host vectors
may expand the number of ops used.
Use QTAILQ to link the ops together.
Backports commit 15fa08f8451babc88d733bd411d4c94976f9d0f8 from qemu
cpu_restore_state officially supports being passed an address it can't
resolve the state for. As a result the checks in the helpers are
superfluous and can be removed. This makes the code consistent with
other users of cpu_restore_state.
Of course this does nothing to address what to do if cpu_restore_state
can't resolve the state but so far it seems this is handled elsewhere.
The change was made with included coccinelle script.
Backports commit 65255e8efdd5fca602bcc4ff61a879939ff75f4f from qemu
The first call of set_cc_op() in a new translation sequence
is done with old_op set to CC_OP_DYNAMIC (-1).
This will do an out of bound access to the array cc_op_live[].
We fix that by adding an entry in cc_op_live[] for CC_OP_DYNAMIC.
Backports commit 7deddf96e94f3e1eb3677db0ea7b53e61751b544 from qemu
Renaming cpu address space names so that they won't be the same when
there are more than one.
Backports commit 87a621d857be1b2b3dd1d0847ca311a863dbcb53 from qemu
Normally we create an address space for that CPU and pass that address
space into the function. Let's just do it inside to unify address space
creations. It'll simplify my next patch to rename those address spaces.
Backports commit 80ceb07a83375e3a0091591f96bd47bce2f640ce from qemu
These gcc warnings are fixed:
target/i386/translate.c:4461:12: warning:
variable 'prefixes' might be clobbered by 'longjmp' or 'vfork' [-Wclobbered]
target/i386/translate.c:4466:9: warning:
variable 'rex_w' might be clobbered by 'longjmp' or 'vfork' [-Wclobbered]
target/i386/translate.c:4466:16: warning:
variable 'rex_r' might be clobbered by 'longjmp' or 'vfork' [-Wclobbered]
Tested with x86_64-w64-mingw32-gcc from Debian stretch.
Backports commit a4926d99129a1d8072fc4681cd4efdb214f65ed4 from qemu
Intel IceLake cpu has added new cpu features,AVX512_VBMI2/GFNI/
VAES/VPCLMULQDQ/AVX512_VNNI/AVX512_BITALG. Those new cpu features
need expose to guest VM.
The bit definition:
CPUID.(EAX=7,ECX=0):ECX[bit 06] AVX512_VBMI2
CPUID.(EAX=7,ECX=0):ECX[bit 08] GFNI
CPUID.(EAX=7,ECX=0):ECX[bit 09] VAES
CPUID.(EAX=7,ECX=0):ECX[bit 10] VPCLMULQDQ
CPUID.(EAX=7,ECX=0):ECX[bit 11] AVX512_VNNI
CPUID.(EAX=7,ECX=0):ECX[bit 12] AVX512_BITALG
The release document ref below link:
https://software.intel.com/sites/default/files/managed/c5/15/\
architecture-instruction-set-extensions-programming-reference.pdf
Backports commit aff9e6e46a343e1404498be4edd03db1112f0950 from qemu
For some systems (i.e. FreeBSD) the default 'make' is not compatible with the
GNU extensions used by QEMU makefiles.
Calling the GNU make (gmake) works, however the help displayed refers to the
host 'make' and copy/paste leads to lot of unobvious errors:
$ gmake check-help
[...]
make check Run all tests
$ make check
make: "Makefile" line 28: Missing dependency operator
make: "Makefile" line 37: Need an operator
make: "Makefile" line 41: warning: duplicate script for target "git-submodule-update" ignored
make: "rules.mak" line 70: warning: duplicate script for target "%.o" ignored
make: Unknown modifier ' '
make: Unclosed substitution for eval modules (= missing)
make: "tests/Makefile.include" line 24: Variable/Value missing from "export"
make: "tests/" line 1: warning: Zero byte read from file, skipping rest of line.
make: "tests/" line 1: Need an operator
make: "Makefile" line 660: warning: duplicate script for target "ifneq" ignored
make: "Makefile" line 78: warning: using previous script for "ifneq" defined here
make: Fatal errors encountered -- cannot continue
Using the $(MAKE) variable, the help displayed is consistent with the 'make'
program used.
Backports commit b98a3bae2596fd9bf60f140d042c8e993daba930 from qemu
This was never used since its introduction in commit
196ea13104f8 ("memory: Add global-locking property to memory
regions").
Backports commit e2fbe20851ceec5ccd7b539a89db0420393fb85d from qemu
SPARC Linux has an oddity that it insists that mmap()
of MAP_FIXED memory must be at an alignment defined by
SHMLBA, which is more aligned than the page size
(typically, SHMLBA alignment is to 16K, and pages are 8K).
This is a relic of ancient hardware that had cache
aliasing constraints, but even on modern hardware the
kernel still insists on the alignment.
To ensure that we get mmap() alignment sufficient to
make the kernel happy, change QEMU_VMALLOC_ALIGN,
qemu_fd_getpagesize() and qemu_mempath_getpagesize()
to use the maximum of getpagesize() and SHMLBA.
In particular, this allows 'make check' to pass on Sparc:
we were previously failing the ivshmem tests.
Backports commit 57d1f6d7ce23e79a8ebe4a57bd2363b269b4664b from qemu
Now that do_ats_write() is entirely in control of whether to
generate a 32-bit PAR or a 64-bit PAR, we can make it use the
correct (complicated) condition for doing so.
Backports commit 1313e2d7e2cd8b21741e0cf542eb09dfc4188f79 from qemu
All of the callers of get_phys_addr() and arm_tlb_fill() now ignore
the FSR values they return, so we can just remove the argument
entirely.
Backports commit bc52bfeb3be2052942b7dac8ba284f342ac9605b from qemu
In do_ats_write(), rather than using the FSR value from get_phys_addr(),
construct the PAR values using the information in the ARMMMUFaultInfo
struct. This allows us to create a PAR of the correct format regardless
of what the translation table format is.
For the moment we leave the condition for "when should this be a
64 bit PAR" as it was previously; this will need to be fixed to
properly support AArch32 Hyp mode.
Backports commit 5efe9ed45dec775ebe91ce72bd805ee780d16064 from qemu
Now that ARMMMUFaultInfo is guaranteed to have enough information
to construct a fault status code, we can pass it in to the
deliver_fault() function and let it generate the correct type
of FSR for the destination, rather than relying on the value
provided by get_phys_addr().
I don't think there are any cases the old code was getting
wrong, but this is more obviously correct.
Backports commit 681f9a89d201d7891e2c60dff5e5415d8f618518 from qemu
Make get_phys_addr_pmsav8() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Backports commit 3f551b5b7380ff131fe22944aa6f5b166aa13caf from qemu
Make get_phys_addr_pmsav7() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Backports commit 9375ad15338b24e06109071ac3a85df48a2cc2e6 from qemu
Make get_phys_addr_pmsav5() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Note that PMSAv5 does not define any guest-visible fault status
register, so the different "fsr" values we were previously
returning are entirely arbitrary. So we can just switch to using
the most appropriae fi->type values without worrying that we
need to special-case FaultInfo->FSC conversion for PMSAv5.
Backports commit 53a4e5c5b07b2f50c538511b74b0d3d4964695ea from qemu
Make get_phys_addr_v6() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Backports commit da909b2c23a68e57bbcb6be98229e40df606f0c8 from qemu
Make get_phys_addr_v6() return a fault type in the ARMMMUFaultInfo
structure, which we convert to the FSC at the callsite.
Backports commit f06cf243945ccb24cb9578304306ae7fcb4cf3fd from qemu
